|
|
|
|
|||
|
|
|
|
Router-CIM Automation Suite 2016 Minimum System Requirements
| • | Windows® 7, Windows® 8/8.1, Windows® 10 (Windows® 10 requires AutoCAD 2016) |
| • | Intel® Pentium® 4 or AMD Athlon™ 64 |
| • | 2GB of RAM (8GB for 3D Modeling) |
| • | 8GB Free disk space for Installation (12GB for 3D Modeling) |
| • | 1,280 x 1,024 True Color video display adapter 128 MB or greater, Pixel Shader 3.0 or greater, Direct3D®-capable workstation-class graphics card (1,600 x 1,050 True Color video display adapter recommended) |
| • | Microsoft® Internet Explorer 9.0 or later web browser with network connection |
| • | .NET Framework Version 4.5 or higher |
| • | 1 Available USB port (2 available USB ports if the nesting option was included) |
| • | DVD Drive |
| • | Windows® 7, Windows® 8/8.1, Windows® 10 (Windows® 10 requires AutoCAD 2016) |
| • | Intel® Pentium® 4 or AMD Athlon™ 64 |
| • | 4GB of RAM (8GB for 3D Modeling) |
| • | 8GB Free disk space for Installation (12GB for 3D Modeling) |
| • | 1,280 x 1,024 true color video display adapter 128 MB or greater, Pixel Shader 3.0 or greater, Direct3D®-capable workstation-class graphics card (1,600 x 1,050 True Color video display adapter recommended) |
| • | Microsoft® Internet Explorer 9.0 or later web browser with network connection |
| • | 128 MB or greater, OpenGL®-capable workstation class graphics card |
| • | .NET Framework Version 4.5 or higher |
| • | 1 Available USB port (2 available USB ports if the nesting option was included) |
| • | DVD Drive |
Supported AutoCAD Versions
Router-CIM 2016 supports the following Autodesk products:
AutoCAD 2014
AutoCAD 2015
AutoCAD 2016
Additionally, we provide an Inventor Link to the following versions of Autodesk Inventor:
Autodesk Inventor 2014
Autodesk Inventor 2015
Autodesk Inventor 2016
You should check your hardware against the Autodesk Certified Hardware List to be sure of compatibility with your version of AutoCAD.
Click here to check Autodesk Certified Hardware List
Hardware Locks
In addition to the hardware requirements listed above, it is important to note that Router-CIM and AutoNEST require hardware locks (often called 'dongles') in order to function. These can be either a USB type or a Parallel Port (printer port) type. Since there are two hardware locks required if you are using the nest software, you should have two USB ports available. For the parallel port type, only one port is necessary since these locks can plug into each other.
Note on Hardware Locks:
The Router-CIM 2007-2016 Hardware Locks are different than the 2004, 2005, and 2006 Hardware Locks. If you are upgrading from a version prior to 2007, you will receive a new Hardware Lock with the 2016 software and will have to return the old Hardware Lock through a traceable carrier. Lost locks are the customer’s responsibility so insure your shipment for full software value. If you fail to return the old lock, you will be invoiced for the full purchase price of the software. If you have Router-CIM 2007 or newer, the hardware locks are compatible and no switch is necessary.
If you are using parallel port hardware locks instead of USB hardware locks, it is not suggested to have a printer, ZIP disk, scanner or any other device connected to the same port as your AutoNest hardware lock. Certain devices may cause hardware lock failure, which will render the software useless until the lock is replaced. Other printing conflicts may occur while printing through the same port as the hardware lock. It may be necessary to have a second parallel port dedicated specifically to the hardware lock.
